DC Motors, AC Motors And Geared Motors

Our product range includes a wide range of 12v dc motor, johnson 12v geared motor, high torque rs-380sh geared dc motor, bo1 dual shaft motor, futaba s3003 servo motor and 5v stepper motors.

12V DC Motor

₹ 299/Piece Get Latest Price

Product Brochure
Voltage12V
Speed<2000 RPM
MaterialCast Iron
CommutationBrush
Packaging TypeBox
BrandLovely Electronics

We are engaged in offering a wide range of 12V DC Motor to our clients. Our range of all products is widely appreciated by our clients.

Johnson 12V Geared Motor

₹ 400/Piece Get Latest Price

Product Brochure
Voltage12 V
Usage/ApplicationIndustrial
TypeExternally Excited
BrandJohnson
Insulation TypeClass A
Packaging TypeBox
Base Motor Speed18000 RPM
MaterialSS
Operating Voltage6-18 V
Rated Torque3.9 kg.cm
Stall Torque15.6 kg.cm
Gearbox Dimensions22 x 37 mm

We are engaged in offering high quality Johnson 12V Geared Motor to our valuable customers.

High Torque RS-380SH Geared DC Motor

₹ 400/Piece Get Latest Price

Product Brochure
Speed15220 RPM at maximum efficiency
Output Power18.6 W
Current4.38 Amp at maximum efficiency
No Load Speed18000 RPM
Stall Torque75.6 mN.m
MaterialSS
Packaging TypeBox
ModelRS-380SH
Nominal Voltage6 V
Stall Current24 Amp
No Load Current0.8 Amp
Operating Voltage3 - 6 V
Torque11.7 mN.m at maximum efficiency

We are engaged in offering high quality RS-380SH Carbon Brush DC Motor to our valuable customers.

BO1 Dual Shaft Motor

₹ 59/Piece Get Latest Price

Product Brochure
Voltage12 V
Speed100 RPM
ApplicationFor Industrial Use
BrandLovely Electronics
No Load Current80 mA
Output Torque4 kg.cm

BO1 Dual Shaft Motor gives good torque and RPM at lower operating voltage, which is the biggest advantage of these motors. Small shaft with matching wheels give optimized design for your application or robot. Mounting holes on the body & light weight makes it suitable for in-circuit placement.

Futaba S3003 Servo Motor

₹ 1100/Piece Get Latest Price

Product Brochure
Voltage4.8 - 6V
BrandFutaba
Usage/ApplicationIndustrial
Model Name/NumberS3003
Connector Wire Length12 inch
Gear TypeNylon Gears
360 ModifiableYes
Stall Torque3.2 kg.cm (4.8V), 4.1 kg.cm (6V)
Operating Temperature-20 to +60 DegreeC
Motor3 Pole Ferrite
Control System+ Pulse Width Control 1520usec Neutral
Potentiometer DriveIndirect Drive
Current Drain7.2 mA/idle (4.8V), 8 mA/idle (6V)
Dimension41 x 20 x 36 mm
Weight37.2 gm
DirectionCounter Clockwise/Pulse Traveling 1520- 1900 u sec
Operating Angle45 Degree one side pulse traveling 400 u sec
Packaging TypeBox
Motor Speed0.23sec/60 degrees at no load (4.8V); 0.19sec/60 degrees at no load (6V)
Bearing TypePlastic Bearing

Futaba servos are your easiest and most efficient way to upgrade your Futaba system. No other system provides you access to as many different sizes, shapes, and functions as Futaba. The performance and reliability of our servos have made them the favorite choice of professionals including top RC competition specialists and motion picture special effect artists. SMT Construction - Surface Mount Technology improves reliability in applications where there is vibration. Impact Resistant, Fuelproof Case - High impact plastic is designed to withstand minor crashes and the effects of model fuel. Through-the-hole Circuit Board Plating - Eliminates the need for wires or leads. Heavy Duty Output Shaft - Designed not to break, and offers versatility when installing the servo horn.

Features:

  • SMT Construction - Surface Mount Technology improves reliability in applications where there is vibration
  • Impact Resistant, Fuelproof Case - High impact plastic is designed to withstand minor crashes and the effects of model fuel
  • Through-the-hole Circuit Board Plating - Eliminates the need for wires or leads
  • Heavy Duty Output Shaft - Designed not to break, and offers versatility when installing the servo horn
  • Nylon gears

5v Stepper Motors

₹ 200/Piece Get Latest Price

Product Brochure
Model Name/Number28BYJ-48
Speed Variation Ratio1/64
Insulated Resistance>10 M ohm
DC resistance50 ohm +/- 7%
Idle In-traction Frequency>600 Hz
Frequency100 Hz
In Traction Torque>34.3 mN.m
Self Positioning Torque>34.3 mN.m
Friction Torque600-1200 gf.cm
Idle Out-traction Frequency>1000 Hz
Noise<35dB
Pull In Torque300 gf.cm
Rise In Temperature<40K
Insulation GradeA
Motor Voltage5V DC
Stride Angle5.625 Degree
Insulated Electricity Power600V AC/1mA/1s

We are offering 5V Stepper Motor. The 28BYJ-48 is a small stepper motor suitable for a large range of applications.

DC Motor Chassis

₹ 149/Piece Get Latest Price

Product Brochure
MaterialStainless Steel
Usage/ApplicationDC Motor
ColorBlack
TypeMounting Plate
Packaging TypeBox
BrandLovely Electronics

We are engaged in offering the high quality range of DC Motor Chassis to our valuable customers.

Johnson Geared Motor Grade B

₹ 500/Piece Get Latest Price

Voltage12 V
Usage/ApplicationIndustrial
Shaft Diameter6 mm (D - shape cut)
No- Load Current100 mA
No Load Current100 mA
Available in following RPM at 12V10, 20, 60, 100, 150, 200, 300, 500, 600
Full Load Current1.9 A

Application - Pan/Tilt camera, auto shutter, welding machines, water meter IC card, grill, oven, cleaning machine garbage disposers, household appliances, slot machines, money detector, automatic actuator, coffee machine, towel disposal, lighting coin refund devices, peristaltic pump.

Stall Torque (kgcm) in relation to RPM

  • 20 rpm - 60
  • 60 rpm - 35
  • 100 rpm - 22
  • 200 rpm - 11
  • 300 rpm - 8
  • 600 rpm - 4

Dc Gear Motor

₹ 285/Piece Get Latest Price

Voltage6 to 24 (Nominal Voltage - 12V)
Usage/ApplicationIndustrial
Load Current300 mA(Max)
Shaft Diameter6 mm (with internal hole)
Weight150 gms approx
Torque3 to 15 kgcm (depending on RPM)
No Load Current60 mA (Max)
Available in following RPM at 12V10, 30, 60, 100, 150, 200, 300, 500 V

Pan/ Tilt camera, auto shutter, welding machines, water meter, IC Card, grill, oven, cleaning machine, garbage disposers, household appliances, Slot machines, Money detector, automic actuator, coffee machine, Towel disposal, lighting, Coin refund devices, Peristaltic pump.

Johnson Geared Motor Grade A

₹ 500/Piece Get Latest Price

Voltage6 to 24 (Nominal Voltage - 12V)
Usage/ApplicationIndustrial
Load Current9 A (Max)
Shaft Diameter6 mm (with internal hole)
Weight300 gms
Motor Diameter28.5 mm
Length Body Only63 mm
Shaft Length15 mm
Base Motor18000 RPM
No Load Current800 mA (Max)
Torque5 kgcm to 20 kgcm (depending on RPM)
Dimensions Gearbox Diameter37 mm
Available in following RPM at 12V30, 60, 100, 150, 200, 300, 500, 1000 V

The Johnson Geared motor is famous for its compact size and massive torque. A torque as much as x3 as compared to center shaft or side shaft geared motor, with an affordable price tag.

The motor comes with a metal gearbox and off centered shaft , also shaft has a metal bushing for wear resistance.

 

Applications:

  • Apart from robotic application they are also used in industrial applications, vending system, hygiene and cleaning industry, and household electric appliance.

12V DC 775 Motor

₹ 300/Piece Get Latest Price

Voltage12V
Efficiency71.8%
No Load Speed7000 rpm
No Load Current0.80 A
Operating Range4.5-12 V
Current Stall Torque36 A
Motor Current5.25 A

We are engaged in offering a wide range of 12V DC 775 Motor to our clients. Our range of all products is widely appreciated by our clients.

RS 50 Gear Motor

₹ 800/Piece Get Latest Price

Speed300 rpm
Power120 W Max
Voltage12 V
Usage/ApplicationIndustrial
Torque Stall60 kgcm
Current60 mA
Torque60kgcm to 10kgcm Depending on RPM
Operating Range12 to 24 V

Heavy DC Geared Motors for Industrial and Robotic Applications.


Typical Applications:

Robotics (robocon events), Pan/ tilt camera, auto shutter, water meter IC card, grill, oven, cleaning machine, garbage dispenser, household appliances, slot machine, money detector, automatic actuator, garbage disposal, lighting, coin refund devices, peristaltic pump, automatic stabilized voltage supply, label printers.

Tauren Gear Motor Series 100

₹ 1200/Piece Get Latest Price

Voltage12 V
Usage/ApplicationIndustrial
Shaft Diameter8 mm
Body Diameter50 mm
Shaft Length18 mm
Torque kgcm15 to 100 (depending on RPM)
Current700 mA to 4 A (max)
Dimension Body Length85 mm max

Gear motors with massive torque (upto 100 kgcm)

 

Application:

  • Pan/Tilt camera auto shutter welding machines water meter IC
  • card grill oven cleaning machine garbage disposers household appliances
  • slot machines money detector automatic actuator coffee machine towel disposal
  • lighting coin refund devices peristaltic pump
  • RPM Available - 100, 150, 350, 625

RS 37-Geared Motor

₹ 400/Piece Get Latest Price

Voltage9 to 18 V (Nominal Voltage - 12V)
Usage/ApplicationIndustrial
Gearbox Diameter37 mm
Length80 mm
Load Current3 A (Max)
Shaft Diameter6 mm (with internal hole)
Weight350 gms
Torque7 to 30 kgcm (depending on RPM)
Available in following RPM at 12V10, 30, 60, 100, 150, 200, 300.V
No Load Current500 mA(Max)
Shaft Length15 mm

Details:

  • RS-37 Gear motor is widely used for Industrial Applications. Carries torque greater as compared to Johnson Motors and consumes less current aswell.
  • This motor has higher durability and is able to work for hours at a time. Base motor RPM is 4500.

JYQD-V7.3E DC 12V 24V 36V 500W Brushless Motor Controller Hall Balanced Car Driver Board

₹ 1400/Piece Get Latest Price

Model No.JYQD-V7.3E2
Usage/ApplicationIndustrial
Input Resistance20 K Ohm
Operating VoltageDC 12-36 V
Operating Current<15A
Speed Control0.1V~5V or PWM Input
PWM Frequency1-20 KHZ
Duty Cycle0-100% br
Drive Power<500W

This is a JYQD V7.3E2 DC 12V-36V 500W Brushless Motor Controller Hall Motor Balanced Car Driver Board. This Brushless Motor Controller DC 12-36V 500W PWM Driver Board is used for the 3-phase brushless sensor-less motor, but not suit for all 3-phase brushless sensor-less motors directly. If the driving effect is not good (such as starting jitter, reversing, the motor no-load working current is too large, the speed is not stable, the efficiency is low, and can’t start-up with a load.) Customers can adjust the resistance and capacitance of the driver board according to the actual situation to achieve the best driving effect.

Pin Description:

  • Control Port: Z/F: Rotating direction control ports. Connect “5V” high level or no connect is Forward direction, connect 0 V low level or connect to GND is reverse direction.
  • VR: Speed control port. Analog voltage linear speed regulation 0.1v -5V, The input resistance is 20K Ohm ,connect with GND when input PWM speed regulation, PWM frequency:1-20KHZ; Duty cycle 0-100%
  • GND: Used for Drive board internal control

Power Port:
  • MA: Motor phase A
  • MB: Motor phase B
  • MC: Motor phase C
  • GND: DC-
  • VCC: DC +
  • Caution: JYQD-V7.3E2 is driver board without housing and heatsink, it can drive the motor below 100 watt without any heatsink, but needs normal ventilation.
  • The 5V output port on the drive board is forbidden to connect external power equipment. It is only applicable to external potentiometer or switch for speed adjustment, commutation and enabling operation

Center Shaft Gear Motor

₹ 95/Piece Get Latest Price

Voltage6 to 24 (Nominal Voltage - 12v)
Usage/ApplicationIndustrial
Shaft Diameter6 mm with internal hole
Weight125 gm
Available in following RPM at 12v3.5, 6, 10, 20, 30, 60, 100, 150, 200, 300, 500, 1000, 2000
Torque1 to 10 kgcm (depending on RPM)
No Load Current60 mA(Max), Load current = 300 mA(Max)

Center Shaft DC Gear motors specifically designed for robotic applications offer a wide variety of options. Key features – easy to use and mount, standard size for all RPM’s, a huge variety of RPM’s available, long durability and very affordable considering the features. These motors open a wide choice for you in terms of Wheels and chasis. Same size motor available in various rpm

Toy Motor - FA130 RA

₹ 10/Piece Get Latest Price

Voltage3 V
Power SourceElectric
Typical ApplicationsHair Dressing, Beauty Appliances, Epilator, Toys & Models
No Load Speed12300 rpm
No Load Current150 mA
Stall Torque36 g.cm
Stall Current2.1 A
Voltage Supply1.5 to 3 V

We are engaged in offering a wide range of Toy Motor - FA130 RA to our clients. Our range of all products is widely appreciated by our clients.

High Torque DC Square Geared Motor

₹ 1000/Piece Get Latest Price

Voltage12 V
Torque115 kg.cm
Model No.HGM-1 Series 170
Speed RPMAvailable in 10, 30, 60, 100, 150, 200, 300 rpm
No- Load Current220 mA
Load Current1.3 A

Application: Towel dispensers, pet devices, vending machines, locks, robots, office equipments, household appliances,egg incubators, etc.


Specifications:

MODEL

VOLTAGE

VDC

NO LOAD

AT STALL

SPEED

CURRENT

TORQUE

CURRENT

WORKING

NOMINAL

Rpm

A

kg.cm

A

HGM-1 Series 170

6-18

12

170

≤1

115

≤14

HGM-1 Series 100

6-18

12

100

≤1

185

≤14

HGM-1 Series 70

6-18

12

70

≤1

260

≤14

Worm Gear Box Reduction Motor 12V Torque

₹ 1450/Piece Get Latest Price

Shaft Length13 mm
Shaft Diameter6 mm
ModelWGM370128500-828K
Motor Length81 mm
Shaft TypeD-type
Motor Width32 mm
Motor Height25 mm

Features: 

  • ALL-METAL GEARS  High-temperature resistance, high abrasion resistance, strong load capacity, sturdy and durable, effectively protect the turbo worm gear box motor body D SHAPED OUTPUT SHAFT  Using high hardness steel, good toughness, impact resistance, the quality of the bearing and the service life of the turbo worm gear motor are improved, extremely durable GEAR DC MOTOR with MICRO-TURBINE WORM  You can change the wiring-connection to change motor rotation. Low noise and high torque.

Specifications:
  • Motor Type - DC Carbon Brush Motor. 
  • Gear Ratio - 828 : 1. 
  • Operating Voltage(VDC) - 12. 
  • Rated Current(A) - 0.220. 
  • Rated Base Motor RPM - 8500. 
  • Rated Speed(RPM) - 10. 
  • Rated Torque (kg-cm) - 10. 
  • Operating Temperature (°C)  - -40 °C   +100°C. 
  • Opt. Relative Humidity(RH) - 20%   85% . 
  • Housing Material - Metal. 
  • Shaft Type - D-type. 
  • Motor Height (mm) - 25. 
  • Motor Width (mm) - 32. 
  • Motor Length(mm) - 81. 
  • Shaft Diameter (mm) - 6. 
  • Shaft Length (mm) - 13. 
  • Shaft Type - D-type. 
  • Motor Weight(gm) - 170.

RS-555 DC Brush Motor

₹ 200/Piece Get Latest Price

Usage/ApplicationIndustrial
No Load Speed4100 rpm
No Load Current0.2 A
Torque up to355 g.cm
Stall Current10.9 A
ModelRS-555
Operating Voltage12-32 V
Stall Torque2977 g.cm

Typical Applications:

  • Precision & Office Equipment, Inkjet printer, Laser Printer, Home appliances, Massager, Vibrator.

59-TYD-375-2A AC Synchronous Motor

₹ 900/Piece Get Latest Price

IP RatingIP30
Voltage240 V
Frequency50-60 Hz
BrandBE
Input power13 W
Motor Weight580 gm
ApplicationBeverage Machine, Blenders, Grill, Oven, Office Equipments, Household Appliances, Etc.
Max Output Torque68 kgcm
Power<10 kw

Main Application:

  • Beverage machine, blenders, grill, oven, office equipments, household appliances, etc.

49TYD-500 Synchronous 5 RPM AC220/240V AC Motor

₹ 80/Piece Get Latest Price

Speed60 RPM
Voltage240 V
Frequency50-60 Hz
TypeSynchronous
Model49TYD-500
Power4 WRPM - 5/6 RPM
Power4 W
No of PhaseSingle Phase

We are engaged in offering a wide range of 49TYD-500 Synchronous 5 RPM AC220/240V AC Motor to our clients. Our range of all products is widely appreciated by our clients.

Tauren Planetary Gear Motor Series PG45

₹ 2000/Piece Get Latest Price

SpeedAvailable in 10, 30, 45, 60, 100, 150, 200, 350 RPM
PowerMax 150 W
Voltage6-18 V
Usage/ApplicationRobotics
Load CurrentMax Load Current 14 A
Shaft Diameter10 mm
Weight1 kg
Dimension Body Length98 mm (max)
Body Diameter50 mm
Shaft Length27 mm
Max Output Torque120 kgcm

Tauren Planetary Gear Motor PG45 Series 

  • Heavy DC Geared Motors for Industrial and Robotic Applications.


Typical Applications:

  • Robotics (robocon events), Electric Controlled valve, robot, wending machine, automatic actuator, automatic doors, coin refund devices, money detector, soft napkin machine, infusion pumps.

TPG28M Planetary Gear DC Motor (Option of Encoder)

₹ 1500/Piece Get Latest Price

PowerUpto 20W
Voltage6-18 V
Usage/ApplicationRobotics
Model NoTPG28M Series
Shaft Diameter6 mm
Weight95 gm
Rated Current0.25 A No load
Rated Base Motor6000 RPM
Diameter of Body28 mm
Rated Speed9, 115, 285, 500 RPM

Planetary Gear DC Motor has the highest continuous and peak torque capability of any gearbox type. They also feature a very compact, low-weight design in their Class. 


Features: 

  • Brushed permanent magnet DC motor. Variable speed and reversible. Planetary Gear Box. Standard brush life of 2000+ hours (varies by application). 

Nema 34 CNC High Torque Stepper Motor

₹ 3499/Piece Get Latest Price

Product Brochure
Step Angle1.8 Degree
Motor TypeBipolor
Dimension86 x 86 x 150 mm
Model Name/Number34HS59-5004S
Number of Leads4
Shaft Length37 mm
D Cut Length25 mm
Holding Torque13 Nm
Lead Length300 mm
Weight5.3 kg
BrandNema
Rated Current5 Amp
Phase Resistance1 ohm
Shaft Diameter14 mm
Inductance11 mH +/- 20% (1 KHz)

This is the strongest Nema 34 CNC High Torque Stepper Motor. It has 4 wires, each phase draws 5 Amp.

TowerPro MG995 Servo Motor

₹ 2200/Piece Get Latest Price

Product Brochure
Voltage4.8 ~ 6.6 V
BrandTowerPro
Model Name/NumberMG995
Gear TypeMetal Gear
Dead Band Width1 us
Weight55 gm
No Load Operating Current Draw170 MA
Stall Current Draw1200 MA
Current Draw At Idle10 MA
Operating Temperature0 to 55 DegreeC
Motor Speed0.20sec/60degree (4.8V); 0.16sec/60degree (6.0V)
Stall Torque9.4 kg.cm (4.8V); 11 kg.cm (6V)
Rotation Angle180 Degree
Servo Wire Length32 cm
Dimension40.7 x 19.7 x 42.9 mm

This is the most famous servo made by TowerPro. MG995 is a digital metal gear high torque servo for airplane, helicopter,  RC-cars from 10 to 6th scale  truggy and monster and many RC model.

Servo arms & crews included and fit with Futaba servo arm. It’s universal “S” type connector that fits most receivers, including Futaba, JR, Hitec ,GWS, Cirrus, Blue Bird, Blue Arrow, Corona, Berg, Spektrum.

We have upgraded our servo gear set and shaft to aluminum 6061-T6. It is stronger and lighter than copper.

Tower Pro MG945 Servo Motor

₹ 420/- Get Latest Price

Product Brochure
Voltage4.8 ~ 6.6 V
BrandTowerPro
Model Name/NumberMG945
Gear TypeMetal Gear
Operating Speed @6.6V0.2sec/60 Degree
Stall Current Draw1200 MA
Operating Speed @4.8V0.23sec/60 Degree
Degree of Rotation180 Degree
Servo Wire Length32 cm
Temperature Range0 to 55 DegreeC
Power Supply TypeThrough External Adapter
Dead Band Width1us
No Load Operating Current draw170 MA
Current Draw At Idle10 MA
Stall Torque10 kg.cm (4.8V); 12 kg.cm (6V)

MG945 is for 1/8 buggy  monster and many RC model. It is low cost of digital servo with export quality and great  servo for just about any application.

Servo arms &s crews included and fit with Futaba servo arm. It’s universal “S” type connector that fits most receivers, including Futaba, JR, Hitec ,GWS, Cirrus, Blue Bird, Blue Arrow, Corona, Berg, Spektrum.

We have upgraded our servo gear set and shaft to aluminum 6061-T6. It is stronger and lighter than copper.

N20 Model - DC 12V Torque Gearbox Micro Gear Box Motor

₹ 300/Piece Get Latest Price

Usage/ApplicationElectronics Equipments
Speed40, 100, 300, 500 RPM
Stall Torque3500 g-cm
No Load Current80 ma
Stall Current1650 mA
Packaging TypeBox
Reduction Ratio1:298
Nominal Voltage6 V
Voltage Range2 -12 V

Applications:

  • Robot, Toys, Automatic door-lock, Camera, Monitor. 

X

Contact Us

Paras Pamnaani (Owner)
Robotskull
2nd Floor Lovely House, Rajmahal Road
Gajara Wadi, Vadodara - 390001, Gujarat, India

Get Directions
Send Email
Share:
Thank youYour Enquiry has been sent successfully.