Robotskull

Ublox NEO-M8N High Precision GPS Module with Built in Compass for APM and PIXHAWK FC is the new Ublox Neo-M8N GPS module that includes an HMC5883L digital compass. This module has a high level of sensitivity and features active circuitry for the ceramic patch antenna. It also comes enclosed in the plastic case to protect the module from the elements. This module outputs precise position updates at 10Hz and also has a rechargeable backup battery for warm starts. The Ublox NEO-M8N is configured to run at a baud rate of 38400 and can be used with Pixhawk and APM (you might need to modify the cable to fit your autopilot board).
Additionally, you can connect the same module to All versions of PIXHAWK Flight Controller just after swapping its 5-pin connector with an extra 6-pin connector provided in Package.So if you want GPS telemetry for your FPV flying or camera ship?  This new generation Ublox GPS NEO-M8N is the answer.  Capable of accuracy between 0.6 and 0.9 meters it is a significant improvement over previous models. Sattelite searching and acquisition is very fast, generally taking around ten seconds to locate and acquire up to 6 satellites.  It also has a built-in compass with a 10Ghz refresh rate and a low noise figure which ensures this GPS module offers excellent performance.
The NEO-M8N provides the best performance and easiest RF integration of all the NEO-M8 configurations. The NEO form factor allows for easy migration from previous NEO generations. Sophisticated RF-architecture and interference suppression ensure maximum performance even in GNSS-hostile environments. NEO-M8 combines a high level of robustness and integration capability with flexible connectivity options. The future-proof NEO-M8N includes an internal Flash that allows simple firmware upgrades for supporting additional GNSS systems.Ublox NEO-M8N GPS Module for APM APM2.52 APM Flight Controller with Case and GPS Antenna Mount to protect the GPS preventing electromagnetic interference. A new generation Ublox GPS NEO-M8N GPS Module, with low power consumption and high precision, the ultimate accuracy is 0.6 meters, actually almost 0.9 meters, greater than the previous generation NEO-7N 1.4-1.6 meters accuracy. Support GPS/QZSS L1 C/A, GLONASS L10F, BeiDou B1 protocol, and mode or more. The NEO-M8N and ceramic antenna make this a very accurate receiver, fast locks & lots of satellites, and the stand is very sturdy to protect the GPS preventing electromagnetic interference.
The most important improvement with this module is the vast sensitivity it offers. This module receives concurrent reception from GPS/QZSS, GLONASS and BeiDou meaning that you should get an excellent signal no matter where you are in the world. Not only does it have these excellent reception capabilities, it maintains its low power consumption. This module is also backward compatible with the NEO-7, NEO-6, and NEO-5 families
Features: 

• GPS/QZSS L1 C/A, GLONASS L10F, BeiDou B1. SBAS L1 C/A: WAAS, EGNOS, MSAS. Galileo-ready E1B/C (NEO-M8N). Nav. update rate1 Single GNSS: up to 18 HZ. Assistance Assist Now GNSS Online. Assist Now GNSS Offline (up to 35 days). Assist Now Autonomous (up to 6 days). OMA SUPL & 3GPP compliant Oscillator TCXO (NEO-M8N/Q). Crystal (NEO-M8M). RTC crystal Built-In. Noise figure On-chip LNA (NEO-M8M). Extra LNA for. lowest noise figure (NEO-M8N/Q). Anti-jamming Active CW detection and removal. Extra onboard SAW bandpass filter (NEO-M8N/Q). Memory ROM (NEO-M8M/Q) or Flash (NEO-M8N). Supported antennas Active and passive. Odometer Travelled distance. Data-logger For position, velocity, and time (NEO-M8N).

The APM 2.5.2/2.6/2.8 Pixhawk Power Module is a simple way of providing your APM 2.5 with clean power from a LiPo battery as well as current consumption and battery voltage measurements, all through a 6-pos cable. The on-board switching regulator outputs 5.3V and a maximum of 2.25A from 2S-6S LiPo battery. The Power Module comes completely assembled with Deans connectors, and wrapped in shrink tubing for protection. 
Note: 

• The Power Module is only designed to power APM, an RC receiver and APM accessories (GPS, 3DR radio). It is not designed to power the servos. Use your aircraft’s own ESC/BEC for that. 

Features: 

• Voltage and current measurement configured for 5V ADC. 
• Switching regulator outputs 5.3V and 3A max. 
• 6-pos DF13 cable plugs directly to APM 2.5’s ‘PM’ connector. 
• Supports from 2 cell to 6 cell battery. 

Package Includes : 

• 1 x APM 2.5.2/2.6/2.8 Pixhawk Power Module V1.0.

• NRF24L01 Module

.

This is a well thought out quad frame built from quality materials. The main frame is glass fiber while the arms are constructed from ultra durable polyamide nylon. Leveraging upon our skilled and accomplished personnel, we are voluntarily engaged in manufacturing, supplying and trading a best grade range of Quad Copter Frame in the national market. These products are sternly checked by our quality analyzers on various parameters to make sure their defect free delivery at customers end. Along with this, these products are available at very cost effective prices.

Features:

• Built from quality glass fiber and polyamide nylon.
• Integrated PCB connections for direct soldering of your ESCs
• Pre-threaded brass sleeves for all of the frame bolts.
• Colored arms for orientation to keep you flying in the right direction.
• Large mounting tabs on main frame bottom plate for easy camera mounting.
• Easy assembly.

The latest version of the popular IMAX B6AC has arrived and now boasts some unique new features. The latest V2 Model now offers PC connectivity which allows the user to control the charger via your home computer and upgrade the firmware as and when necessary.The B6AC V2 now gives you the ability to adjust the terminal voltage, which makes the charger the perfect charging solution for heavy duty batteries.
The B6AC V2 can also be used as a Lithium battery meter / internal resistance meter and boasts additional functions which include, automatic charging current limit, capacity limit and processing time limit, making the B6AC V2 one of the safest chargers available today.
Features:

• PC connectivity
• Microprocessor controlled
• Delta-peak sensitivity
• Individual cell balancing
• Li-ion, LiPo and LiFe capable
• Ni-Cd and NiMH capable
• Large range of charge currents and automatic charge current limit
• Store function, allows safe storage current
• Time limit function
• Input voltage monitoring (Protects car batteries at the field)
• Data storage (5 pack memory)
• Battery break in and cycling.
• Terminal voltage adjustment for heavy duty batteries

Package Includes: 

• 1 x IMAX B6AC V2 Charger 1 x DC Jack plug to crocodile clips 1 x male T connector charge lead to 4mm banana plugs 1 x XT60 charge lead 1 x JST charge lead1 x Crocodile clip charge lead 1 x Futaba style charge lead 1 x Mains power lead (US type)

We are engaged in offering high quality range of Coreless Drone Motor to our valuable clients.

The pack includes two propeller blades with adapters (1 CW and 1 CCW), similar to the photo displayed (color might be different)


The propeller(s) are avalilable in the following sizes :

• 5 x 4.5 aka 5045 + 5045R
• 6 x 4.5 aka 6045 + 6045R
• 7 x 4.5 aka 7045 + 7045R
• 8 x 4.5 aka 8045 + 8045R
• 9 x 4.5 aka 9045 + 9045R
• 10 x 4.5 aka 1045 + 1045R
• 12 x 4.5 aka 1245 + 1245R

Set of counter rotating RC aircraft propellers perfect for use in twin and multiple motor RC airplanes or coaxial RC helicopters. You receive 2 propellers: one propeler rotates clockwise ( CW ) and the other propeler rotates counter clockwise ( CCW ) (1 left hand 1 right hand rotation). These matched rotor blades are a hard to find matched counter rotating pair.

The Micro MinimOSD with all the features of the very popuar WiteSpy KV Team modded OSD but in a 16x16mm size. Doesn't have the DC/DC converter, this means less heat when powered off a flight controller. The Micro MinimOSD is the same as the older MinimOSD hardware, but has been modified to take advantage of custom firmware options. You can choose firmware that is MAVLink compatible for ArduCopter, or MultiWii Serial compatible for MultiWii and Baseflight / Cleanflight control boards. You can connect two batteries up to 4S so you can see the main flight battery voltage. the second port will allow your FPV battery voltage on the display as well.  
Description: NO DC/DC converter, power board via 5 voltsFTDI cable compatible pinout Standard 6-pin ISP header Two LED indicators ATmega328P with Arduino boot loader MAX7456 monochrome on-screen display 16 x 16mm Size Pad for an Analog or Digital PWM RSSI signal Pad for the connection of a Current Sensor ATmega 328P with Arduino boot loader Standal one, or with APM / Flip / Flip32+ flight controllers These modifications allow direct connection of two batteries (up to 4S) This hardware take the hardware mods for this firmware, and builds them into an RTF solution. This Board can be used just as a normal OSD for APM or it can be used with MWC KV Team Mod. Two independent power sections with an LED indicator on each. Solder jumpers for combining the power sections Solder jumper for PAL video option+5V 500mA regulator for up to +12V supply input Exposed test points for HSYNC and LOS.
Package included: 1 x Micro Minim OSD board2 x pins (sets)

F550 is a multi-rotor designed for all pilots for fun or AP. With DJI WKM or NAZA autopilot system, it can achieve hovering, cruising, even rolling and other flight elements. It can be applied for entertainment, aerial photography, FPV and other activities. Made by advanced engineering material, super strong & smooth Kit (need assemble by yourself ). New design PCB board special for F550, support standard flight controller like MK, KK, FF, MWC, APM.

Features:

• F450 is a multi-rotor designed for all pilots for fun or AP.
• It can achieve hovering, cruising, even rolling and other flight elements.
• It can be applied for entertainment, aerial photography, FPV and other aeromodelling activities.
• Support standard flight controller like MK, KK, FF, MWC, APM
• DJI F450 Hexacopter basic frame wheel kit.
• Using high strength compound PCB frame board, which makes wiring of ESCs and battery more easily.

F550 Flame Wheel:

• Color: Black + White + Red
• Frame Arm Size: 215 x 38 x 50mm
• Weight: 54g (Single)
• Weight: 324g (6pcs)

F550 Multicopter Frame Center Plate:

• Color: Black
• Material: Glass Fiber
• Use For DJI F550 Hexacopter

Recommended Config (Not Included):

• Propeller: 10 x 4.5in; 8 x 4.5in
• Battery: 3S~4S LiPo
• Motor: 22 x 12mm (Stator size)
• ESC: 30A OPTO or 18A
• Package Weight: 605g
• Package Dimension (L x W x H): 255 x 250 x 50mm
• After Sales Service: 1 Year Warranty

Package Include:

• 6 x Flame Wheel (2 Red, 2 Black, 2 White)
• 1 x F550 Top Plate
• 1 x F550 Bottom Plate
• 2 x Small Bag of Screws

Features:

• Built from quality glass fiber and polyamide nylon.
• Integrated PCB connections for direct soldering of your ESCs
• Pre-threaded brass sleeves for all of the frame bolts.
• Colored arms for orientation to keep you flying in the right direction.
• Large mounting tabs on main frame bottom plate for easy camera mounting.
• Easy assembly.

FlySky CT6B 2.4Ghz 6CH Transmitter with FS-R6B Receiver is the popular 6 Channel Radio CT6B manufactured by FlySky. CT6B FLYSKY 2.4GHZ 6CH TRANSMITTER is an entry-level 2.4 GHz radio system offering the reliability of 2.4 GHz signal technology and a receiver with 6 channels. CT6B FLYSKY 2.4GHZ 6CH TRANSMITTER radio is a value for money, entry level 6 channel transmitter, ideal for quadcopters and multicopters that require the 6ch operation.

This radio has two retract switches and proportional flap dials in easy reach for channels 5 and 6. It can be powered by 8 x AA Size Batteries or a 12V Power Supply. It comes with a trainer port to help beginners learn flying.It can be configured by connecting it to the computer. Use the T6config software to configure your radio on a computer.

Features : 

• Super active and passive anti-jamming capabilities.
• Very low power consumption.
• High receiving sensitivity.
• 8 model memory, digital control.
• Can be programmed by PC with included software.
• Full range 2.4GHz 6-channel radio.
• 4-Model
• 4 Types (Airplane, Heli90, Heli120, Heli140).
• Integrated
• Contrast Adjustment.
• Throttle cut.
• Computer
• USB Socket.
• Use a linear spread of fine paragraph by excess antenna.
• It covers the entire band width of he antenna bandwidth range.
• High quality and stability.

Package Includes :

• 1 x FS-CT6B Transmitter
• 1 x FS-r6B Receiver
• 1 x USB Interface Cable
• 1 x Software CD
• 1 x Receiver Binding Cable
• 1 x User Manual

This is the FlySky FS-i6 2.4G 6CH PPM RC Transmitter With FS-iA6B Receiver. This is a great entry-level radio for those just starting in the field of drones flying due to the ease of use of this product and an impressive list of features for a first-time radio. FlySky FS-i6 2.4G 6CH PPM RC Transmitter is a 6-channel telemetry 2.4GHz transmitter that uses the reliable Automatic Hopping Digital System (AFHDS) and includes such features as digital trims, backlit LCD screen, and simple programming.

On top of this, you get a slim, modern radio transmitter that fits nicely in your hands and weighs just under 400g and so won’t test your arm stamina on those long flights. This radio is also really practical with a 3-position switch as well as two adjustable knobs for flight modes/ multiple flap positions.

You also get the new FS-iA6B receiver with this kit. This is a compact 6-channel receiver with a range exceeding 500m and it comes with a dual antenna for excellent reception and interference rejection capabilities.  Each transmitter has a unique ID and so when binding, the receiver remembers this ID and accepts data from that transmitter only. This avoids picking up other transmitter signals and dramatically decreases inference and increases safety.

Features:

• Entry-level 6 channel 2.4GHz radio with telemetry capability.
• Dual Rate/Trims/Gear/Flap/Gyro Gain Adjust/Flight Mode/Throttle Hold/Hover Pitch Switches.
• Easy to use Programming & Navigation Buttons.
• Supports Heli/Standard Wing/Elevon/V-Tail.
• 20 Model Memory.
• 8 Character Model Name.
• Trainer and charging ports.
• The backlit LCD screen displays real-time transmitter and receiver voltage.
• 4 Stick Mode Selectable.
• Mode 2.
• It comes with a receiver.
• Entry-level 6 channel 2.4GHz radio with telemetry capability.
• Dual Rate/Trims/Gear/Flap/Gyro Gain Adjust/Flight Mode/Throttle Hold/Hover Pitch Switches.
• Easy to use Programming & Navigation Buttons.
• Supports Heli/Standard Wing/Elevon/V-Tail.
• 20 Model Memory.
• 8 Character Model Name.
• Trainer and charging ports.
• The backlit LCD screen displays real-time transmitter and receiver voltage.
• 4 Stick Mode Selectable.
• Mode 2.
• It comes with a receiver.

LIPO battery fast charging with wide AC input. An internal 100-240V AC switch power is built in, and the high precision balance circuit can supply larger current up to 850mA per cell. Double color LED can display the process of charging (RED: charging; GREEN: full). This charger is compact and light; especially there is separated corresponding balance port for each battery pack.

A2212 BLDC Motor for Quadcopter available in below KV - 

• 1000KV 
• 1400KV
• 1800KV
• 2200KV

We are engaged in offering high quality range of Coreless Motor to our valuable customers.

Electronic Speed Controller (ESC) 30A is a electronic circuit to vary the speed, direction and possible to act as a dynamic brake, of a Brushless Motor. This particular ESC is recommended with A2212 brushless motor (1000kv, 1400kv, 2200kv).

 

Keeping our harmonization with the market defined quality parameters; we are widely reckoned for providing a flawless array of Electronic Speed Controller ESC 30A to our respected clients. Our offered speed controllers are highly known in electronic industries for controlling the speed. Apart from this, we ensure to deliver these products within stipulated time frame.

Features:

• Dimensional Accuracy
• Fine finish
• Affordable

LIPO Battery Voltage Tester and low voltage buzzer alarm combo is easy to use. can save your model/batteries and investment. This is a new product combining all the voltage measurements with low-voltage alarm function. Li-Po Battery Voltage Buzzer+Indicator: directly plug it into your operating battery, it will monitor the conditions of your battery all the time, so your batteries shall remain within safe operating voltage range at all times.
Features:

• Low voltage Buzzer alarm mode for 2-8S.
• With a push key by which you can change the value settings and save.
• When voltage is below the set value, it will buzzer very loudly with red LED light. (pre-set value is 3.3V)
• Mini shape, no larger than a common key.
• Compact, easy to carry.
• Really useful in flight if you can't see the lights.
• Use for 1-8s Lipo/Li-ion/LiMn/Li-Fe.
• Voltage detection precision: ±0.01V
• Unit voltage display range: 0.5-4.5V
• Total Voltage display Range: 0.5-36V
• 1S test mode voltage range: 3.7-30V
• 1S test mode detection precision: ±0.5%

The KK-Mini is the next Big/Small evolution of the first generation KK flight control boards. The KK-Mini is based on the KK2.1.5 architecture and has all the same inputs and outputs as well as the full functionality of its big brother. The new 36mm designed was adapted to fit the needs of the new mini market, but don't let its size fool you as it's just as much at home in any size multi-rotor. The KK mini still utilizes a built in GUI using a hi-res mini LCD and 4 micro buttons for the same great KK experience. It was engineered from the ground up to bring multi-rotor flight to everyone, not just the experts.

 

The original KK gyro system has been updated to an incredibly sensitive 6050 MPU system, making this the most stable KK board ever and allowing for the addition of an auto-level function. At the heart of the KK-Mini is an Atmel Mega644PA 8-bit AVR RISC-based microcontroller with 64k of memory. An additional polarity protected header has been added for voltage detection, so no need for on-board soldering. A handy piezo buzzer is also included for audio warning when activating and deactivating the board.

Features:

• Channels: 6 Channels
• Model Type: Heli, Airplane, Gliders RF
• Power: Less than 20db
• Modulation: GFSK
• Code Type: PCM
• Sensitivity: 1024
• Low Voltage Warning: LED
• DSC Port: Yes
• Charger Port: Yes

Package Includes:

• FS-R6B Receiver The transmitter requires a PC to modify any of the channel variables, including mixing and servo reversing.