Robotskull

Details:

• Step Angle – 1.8 deg
• Voltage/Phase – 4v
• Current/Phase – 0.95A
• Resistance/Phase – 4.2ohms
• Inductance/Phase – 2.5mH
• Holding Torque – 16 N.cm
• No. of Leads – 6
• Rotor Inertia – 35 g.cm2
• Weight – 0.22 kg
• Length – 33mm
• Step Angle Accuracy – (+-) 5%
• Resistance Accuracy – (+-) 10%
• Inductance Accuracy – (+-) 20%

Specifications:

• Rated Voltage (V) - 4.2
• Current/ phase (A) - 4
• Holding Torque (kg-cm) - 68
• No. of Leads - 4
• Length (mm) - 95
• Step Angle - 1.8°
• Step Angle Accuracy - ±5% (full step, no load)
• Resistance Accuracy - ±10%
• Inductance Accuracy - ±20%
• Frame Size (mm) - 85x85
• Shaft Length (mm) - 32
• Shaft Diameter (mm) – 12

Bldc Motor Specifications:

• Manufactuer Model - Jk86bls125
• Number Of Poles - 8 Poles
• Phase To Phase Resistance - 0.8 Ohms
• Nominal Voltage - 310 Vdc
• No Load Speed - 3500 Rpm (10% Variation)
• No Load Current - 1 Amps Max.
• Rated Torque - 6.6 N-m
• Rated Speed - 3000 Rpm (10% Variation)
• Rated Current - 7.7 Amps
• Output Power - 2.07 Kw
• Back Emf Constant - 88.6 V/krpm
• Torque Constant - 0.845 N-m/a
• Insulation Class - H

Electric Connections:

• +5v - Red
• Hall U - Yellow
• Hall V - Green
• Hall W - Blue
• Gnd - Gnd
• Phase U - Yellow
• Phase V - Green
• Phase W - Blue

Motor Specifications:

• Number of Phase - 2
• Step Angle - 1.8 deg
• Rated Voltage - 3.78 V
• Rated Current - 4.2A (Peak Value)
• Phase Resistance - 0.9 ohm
• Phase Inductance - 4 mH (1kHz 1V RMS)
• Holding Torque - 30 kg.cm
• Weight - 1.4 kg
• Insulation Class - B (130) 80K Max
• Motor with 1000 ppr encoder
• 20V ~ 50VDC 0.1A - 10A NEMA23 Closed Loop Stepper Motor Driver JK-HSD57
• Features of closed loop stepper motor
• Step and direction control
• Closed position loop for no loss of movement synchronization
• Operating voltage: 20-50 VDC
• Load based output current of 0.1 - 10 A
• High torque at starting and low speed
• No torque reservation
• High stiffness at standstill
• Significantly reduced motor heating
• Smooth motor movement and extra low motor noise
• Quick response, no delay and zero settling time
• No loss of steps; no hunting; no overshooting
• Plug-and-play and no tuning
• Descriptions of NEMA23 stepper driver

JK-HSD57 is one of the models in Jkongmotor series easy servo drives which can take 20-50 VDC operating voltage and output 0.1 -10A continuous load-based current. It is capable of driving NEMA 17, 23, 24 and 34 easy servomotors (stepper motors with encoders) with the position loop closed in real time.

Based on latest DSP technology and adopting Novo's advanced control algorithm, JK-HSD57 easy servo drive applies servo control on easy servo motors. When adopted with an easy servo motor, it combines features of both open loop steppers & brushless servo systems, and offers many unique advances features for excellent motion control system performance.

When an JK-HSD57 easy servo drive is implemented with a novo SC series easy servo motor, there is No Configuration Needed for almost all applications. The output resolution from JK-HSD57 with the output resolution defaulted to output resolution of 2,000 pulses per resolution (equal to 10 microstep in 2-phase stepper systems). Via DIP switches, a user can also easily change the output resolution to one of 15 output resolutions 400 to 51,200 (equal to 2-256 microstep in 2-phase stepper systems). With novo configuration software, ProTuner, an advanced user can also set custom settings of resolution, current & position loop parameters, idle current percentage, etc.

Applications:

• With many unique advanced features, JK-HSD57 easy servo systems are ideal for many industries to upgrade stepper performance or replace brushless servo systems in many applications.
• Jkongmotor OEM clients have successfully implemented JK-HSD57 driven easy servo systems in applications such as small-to-large size CNC routers, CNC mills, plasmas, large-scale laser cutters / engravers, labeling equipments,robotics, gemstone processing machines, pick & place machines, X-Y tables.

Motor Specifications:

• Number of Phase - 2
• Step Angle - 1.8 deg
• Rated Voltage - 3.78 V
• Rated Current - 4.2A (Peak Value)
• Phase Resistance - 0.9 ohm
• Phase Inductance - 4 mH (1kHz 1V RMS)
• Holding Torque - 30 kg.cm
• Weight - 1.4 kg
• Insulation Class - B (130) 80K Max
• Motor with 1000 ppr encoder
• 20V ~ 50VDC 0.1A - 10A NEMA23 Closed Loop Stepper Motor Driver JK-HSD57

Features of closed loop stepper motor:

• Step and direction control
• Closed position loop for no loss of movement synchronization
• Operating voltage: 20-50 VDC
• Load based output current of 0.1 - 10 A
• High torque at starting and low speed
• No torque reservation
• High stiffness at standstill
• Significantly reduced motor heating
• Smooth motor movement and extra low motor noise
• Quick response, no delay and zero settling time
• No loss of steps; no hunting; no overshooting
• Plug-and-play and no tuning

Descriptions of NEMA23 stepper driver:

• JK-HSD57 is one of the models in Jkongmotor series easy servo drives which can take 20-50 VDC operating voltage and output 0.1 -10A continuous load-based current. It is capable of driving NEMA 17, 23, 24 and 34 easy servomotors (stepper motors with encoders) with the position loop closed in real time.
• Based on latest DSP technology and adopting Novo's advanced control algorithm, JK-HSD57 easy servo drive applies servo control on easy servo motors. When adopted with an easy servo motor, it combines features of both open loop steppers & brushless servo systems, and offers many unique advances features for excellent motion control system performance.
• When an JK-HSD57 easy servo drive is implemented with a novo SC series easy servo motor, there is No Configuration Needed for almost all applications. The output resolution from JK-HSD57 with the output resolution defaulted to output resolution of 2,000 pulses per resolution (equal to 10 microstep in 2-phase stepper systems). Via DIP switches, a user can also easily change the output resolution to one of 15 output resolutions 400 to 51,200 (equal to 2-256 microstep in 2-phase stepper systems). With novo configuration software, ProTuner, an advanced user can also set custom settings of resolution, current & position loop parameters, idle current percentage, etc.

 Applications:

• With many unique advanced features, JK-HSD57 easy servo systems are ideal for many industries to upgrade stepper performance or replace brushless servo systems in many applications.
• Jkongmotor OEM clients have successfully implemented JK-HSD57 driven easy servo systems in applications such as small-to-large size CNC routers, CNC mills, plasmas, large-scale laser cutters / engravers, labeling equipments,robotics, gemstone processing machines, pick & place machines, X-Y tables.

Nema 17 is the motor of choice for RepRaps/3D printers/ Desktop CNC Routers. It is also a suitable motor for various robotics applications. This motor is the most preferred motor used by the rep rap community. 
Specifications:

• Step Angle : 1.8 deg Step 
• Angle Accuracy : +/- 5% 
• Resistance Accuracy : +/- 10%
• Inductance Accuracy : +/- 20%
• Temprature Rise : 80 deg C 
• Max Ambient Temerature : -10 deg C +50 deg C 
• Insulation Resistance : 10 M Ohms Min.
• 500VDC Dielectric Strength : 500 VAC for one minute
• Shaft Radial Play : 0.02 Max (450 g-load) 
• Shaft Axial Play : 0.08 Max (450 g-load)
• Current A - 1.5
• Resistance (ohms) - 2.8
• Inductance (mH) - 5.5
• Holding Torque N.cm - 55
• Detent Torque N.cm - 2.6
• No. of Leads - 4 (bipolar)
• Weight - 350g 
• Length - 48mm

Specifications:

• Rated Voltage (V) - 6.6
• Current/ phase (A) - 1
• Resistance/ phase (ohms) - 6.6
• Inductance/ phase (mH) - 8.2
• Holding Torque (kg-cm) - 7.2
• No. of Leads - 6
• Rotor Inertia - 275
• Weight (kg) - 0.65
• Detent Torque (kg-cm) - 0.36
• Length (mm) - 51
• Step Angle - 1.8°
• Step Angle Accuracy - ±5% (full step, no load)
• Resistance Accuracy - ±10%
• Inductance Accuracy - ±20%
• Frame Size (mm) - 57x57
• Shaft Length (mm) - 20.6
• Shaft Diameter (mm) - 6.35
• Length (mm) - 51
• Weight (kg) - 0.65

Details:

• 32-bit DSP control, low noise and superior vibration performance
• 16 constant torque microstep setting, up to 200 microsteps
• Smooth and accurate current control, High-speed output increased by 7%, effectively reduce motor heating
• The highest pulse response frequency is 200KHZ
• When the pulse stops over 250ms, the motor current is halved
• Excellent smoothness in low frequency high microstep applications
• Optically isolated differential signal input, strong anti-interference ability
• Driver current is adjustable below 3.0A
• Voltage input range: DC20~50V
• With over voltage, under voltage etc. fault protection
• Small size, volume 118*76*24.2 (mm³), 
• Weight 0.3kg
• Suitable for 42~86mm(NEMA17~34) 2 phase open-loop stepper motors.

The DMA860HH is a high performance microstepping driver based on pure-sinusoidal currentcontrol technology. Owing to the above technology and the self-adjustment technology (self-adjustcurrent control parameters) according to different motors, the driven motors can run with smallernoise, lower heating, smoother movement and have better performances at higher speed than mostof the drivers in the markets. It is suitable for driving 2-phase and 4-phase hybrid stepping motors.

Features:

• High performance, cost-effective
• Supply voltage up to 80VAC or +110VDC Output current up to 7.2A
• Self-adjustment technology Pure-sinusoidal current control technology
• Pulse input frequency up to 300 KHzTT compatible and optically isolated input
• Automatic idle-current reduction
• 16 selectable resolutions in decimaandbinary, up to 51,200 steps/rev
• Suitable for 2-phase and 4-phase motorsSupport PUL/DIR and CW/CCWmodes
• Short-voltage, over-voltage, over-current and short-cicuit protection

This is essentially a ramped up version of our Ardumoto motor driver shield. For this Monster Moto Shield we’ve replaced the L298 H-bridge with a pair of VNH2SP30 full-bridge motor drivers. We’ve also beefed up the support circuitry so this board is capable of driving a pair of high-current motors! The VIN and motor out are pitched for our 5mm screw terminals (not included), making it easy to connect larger gauge wires.
Note: When using this board in extreme high-demand applications it may be necessary to improve thermal performance with a heat-sink or fan and to solder the wires directly to the board instead of using a screw terminal (in addition to the myriad other complications present in a high-current system) However, when using the board at currents up to 6A the chips will barely become noticeably warm.
Details:

• Voltage max: 16V
• Maximum current rating: 30 A
• Practical Continuous Current: 14 A
• Current sensing available to Arduino analog pin
• MOSFET on-resistance: 19 mΩ (per leg)
• Maximum PWM frequency: 20 kHz
• Thermal Shutdown
• Under voltage and Overvoltage shutdown

TB6600 stepper motor Driver Controller 4A 9~42V TTL 16 Micro-Step CNC 1 Axis NEW upgraded version of the 42/57/86 stepper motor.

Package includes:

• 1pcs TB6600 4-aixs stepper motor driver

Detail Description:

• This drive is an upgraded version of TB6600, segment increased to 32 segments, suitable for high subdivision applications . 
• Suitable for step motor: 57, 42, 86
• Type 4 phase 2 phase (4 line 6 line 8)
• 9V-42V DC power supply.
• H bridge bipolar constant current drive .
• The biggest4.0AEight kinds of output current are optional .
• The biggest32To subdivide6 kinds of subdivision modes selectable .
• Input signal high speed photoelectric isolation .
• A total of standard single pulse interface .
• Offline retention function .
• Semi enclosed casing can adapt to more stringent environment .
• Provide energy saving half automatic current lock function .

MACH3 Interface Board CNC 5 Axis with Optocoupler latest upgrade 5 axis breakout board is specially designed for the CNC single axis 2-phase stepper driver controller, such as TB6560, M542, M542H, MA860H, 2M542, 2M982, DM542(A), DM860(A) etc. single axis stepper driver controller series. With this 5 axis breakout board, any 1-5 single axis stepper driver controllers can be directly controlled by the PC via the MACH3, EMC2, KCAM4, etc

• Features :Maximum support 5-axis stepper motor driver controllers
• Compatible with MACH3, Linux CNC (EMC2) etc. parallel-control CNC software.
• USB power supply and peripherals power phase are separate to protect computer security.
• All the signals are to-isolate which can protect your computer security.
• 5-input interface to define the Limit, Emergence-Stop, Cutter alignment, etc.
• Wide input voltage range: 12-24V, and with anti-reverse function.
• One relay output control interface, accessed by the spindle motor or the air pump, water pump, etc.
• Output 0-10V analog voltage for the inverter to control the spindle speed.
• All the way to the relay output port, control spindle switch. Output port P17 mouth.
• Open all 17 ports, which can be accessed with the optocoupler drive, 5-axis stepper motor can be controlled.
• Pin P1 as PWM outputs can be controlled with optocoupler input spindle governor.
• Can be accessed by a common cathode or common anode input level to 5V drive.
• All the way through the optocoupler isolated 0-10V analog voltage output can be controlled with the corresponding analog interface converter to control the spindle speed. Output port P1 port.

Features :

• USB power supply and peripherals power phase are separate to protect computer security.
• All the signals are to-isolate which can protect your computer security.
• 5-input interface to define the Limit, Emergence-Stop, Cutter alignment, etc.
• Wide input voltage range: 12-24V, and with anti-reverse function.
• One relay output control interface, accessed by the spindle motor or the air pump, water pump, etc.
• Output 0-10V analog voltage for the inverter to control the spindle speed.
• All the way to the relay output port, control spindle switch. Output port P17 mouth.
• Open all 17 ports, which can be accessed with the optocoupler drive, 5-axis stepper motor can be controlled.
• Pin P1 as PWM outputs can be controlled with optocoupler input spindle governor.
• Can be accessed by a common cathode or common anode input level to 5V drive.
• All the way through the optocoupler isolated 0-10V analog voltage output can be controlled with the corresponding analog interface converter to control the spindle speed. Output port P1 port.
• Features :
• Maximum support 5-axis stepper motor driver controllers
• Compatible with MACH3, Linux CNC (EMC2) etc. parallel-control CNC software.
• USB power supply and peripherals power phase are separate to protect computer security.
• All the signals are to-isolate which can protect your computer security.
• 5-input interface to define the Limit, Emergence-Stop, Cutter alignment, etc.
• Wide input voltage range: 12-24V, and with anti-reverse function.
• One relay output control interface, accessed by the spindle motor or the air pump, water pump, etc.
• Output 0-10V analog voltage for the inverter to control the spindle speed.
• All the way to the relay output port, control spindle switch. Output port P17 mouth.
• Open all 17 ports, which can be accessed with the optocoupler drive, 5-axis stepper motor can be controlled.
• Pin P1 as PWM outputs can be controlled with optocoupler input spindle governor.

General Specification: 

• Current / Phase: 1.5A. 
• Step Angle(degrees): 1.8. 
• Phase: 2.  
• Type: Hybrid. 
• Certification: ROHS,CE. 
• Holding Torque: 4.2 KGCM.  
• Step angle accuracy: + - 5%(full step,not load). 
• Resistance accuracy: + - 10%. 
• Inductance accuracy: + - 20%. 
• Temperature rise: 80deg Max (rated current,2 phase on). 
• Ambient temperature : 20deg ~+50deg. 
• Insulation resistance: 100M Min,500VDC. 
• Insultion Strength - 500VAC for one minute. 
• Lead Screw Material: 304 Stainless Steel. 
• Color:Sliver. 
• Diameter: 8mm. 
• Length: 300mm. 
• Lead of thread: 8mm. 

Package Included: 

• 1x 17HS4401 Stepper Motor. 1x 300mm Lead Screw. 1x T8 Nut.

Step and direction control Closed position loop for no loss of movement synchronization Operating voltage: 20-50 VDC Load based output current of 0.1 - 10 A High torque at starting and low speed No torque reservation High stiffness at standstill Significantly reduced motor heating Smooth motor movement and extra low motor noise Quick response, no delay and zero settling time No loss of steps; no hunting; no overshooting Plug-and-play and no tuning.
Descriptions of NEMA23 stepper driver:

• JK-HSD57 is one of the models in Jkongmotor series easy servo drives which can take 20-50 VDC operating voltage and output 0.1 -10A continuous load-based current. 
• It is capable of driving NEMA 17, 23, 24 and 34 easy servomotors (stepper motors with encoders) with the position loop closed in real time. 
• Based on latest DSP technology and adopting Novo's advanced control algorithm, JK-HSD57 easy servo drive applies servo control on easy servo motors. 
• When adopted with an easy servo motor, it combines features of both open loop steppers & brushless servo systems, and offers many unique advances features for excellent motion control system performance. 
• When an JK-HSD57 easy servo drive is implemented with a novo SC series easy servo motor, there is No Configuration Needed for almost all applications. 
• The output resolution from JK-HSD57 with the output resolution defaulted to output resolution of 2,000 pulses per resolution (equal to 10 microstep in 2-phase stepper systems). 
• Via DIP switches, a user can also easily change the output resolution to one of 15 output resolutions 400 to 51,200 (equal to 2-256 microstep in 2-phase stepper systems). 
• With novo configuration software, ProTuner, an advanced user can also set custom settings of resolution, current & position loop parameters, idle current percentage, etc. 

Applications:

• With many unique advanced features, JK-HSD57 easy servo systems are ideal for many industries to upgrade stepper performance or replace brushless servo systems in many applications.
• Jkongmotor OEM clients have successfully implemented JK-HSD57 driven easy servo systems in applications such as small-to-large size CNC routers, CNC mills, plasmas, large-scale laser cutters / engravers, labeling equipments, robotics, gemstone processing machines, pick & place machines, X-Y tables.

Electrical Specifications: 

• Number of Phase - 2
• Step Angle - 1.8 deg
• Rated Voltage - 1.68V 
• Rated Current - 4.2A 
• Phase Resistance - 0.4 ohm Phase 
• Inductance - 1.5 mH (1kHz 1V RMS) 
• Holding Torque - 12 kg.cm 
• Weight - 0.68kg 
• Insulation Class - B (130) 80K Max Motor with 1000 ppr encoder
• Input Voltage - 20 to 50 VDC 
• Output Current - 0.1 to 10A (Max) 
• Pulse Input Frequency - 0 - 200 kHz 
• Logic Signal Current - 7 - 16 mA 
• Isolation Resistance - 500 M ohm

This Stepper Motor Controller Board is based on the TOSHIBA 2SC5200. This board can be used to generate PWM signals for the stepper motor driver, it has onboard buttons for the CW and CCW rotation of the stepper motor. The speed of the motor can be varied through the onboard potentiometer. When the board generates a frequency pulse signal, the high and low-frequency signal can be selected by the onboard jumper.

Note:

• If you want to use the start or stop function, the ENA enable terminal on the controller must be connected to the driver with a common cathode or a common anode.
• The forward and reverse rotation and the start and stop of the motor can be controlled by pressing the button.
• The speed of the motor can be controlled by adjusting the potentiometer to change the frequency.
• The switch of the motor’s forward / reverse rotation and start/stop is an ordinary switch with self-locking.
• If you want to connect the switches that control forward and reverse, and open or stop, to the chassis panel, you can refer to the following instructions
• Change the forward and reverse, the start-stop button into a lead-wire switch, see the pin position on the back

Features:

• It has three frequency ranges selectable via onboard jumpers.
• Frequency can be measured via PUL and common cathode (GND) ports.
• The board has two sets of power input

Specification:

• Power supply: DC15-80V or DC 12V
• High frequency: 5.8KHZ-127KHZ
• Middle frequency: 590HZ-15.8KHZ
• Low frequency: 82HZ-2.3KHZ
• Measuring frequency interface: PUL, GND

Package Includes:

• 1 x Stepper Motor Drive Simple Controller Speed Forward and Reverse Control Pulse Generation PWM Generation Controller

Main features:

• It can be connected with an external speed display board, showing the speed; it can also be connected with computers to set drive parameters.
• It has double speed closed current design with low speed torque and smooth operation;
• It has high speed output with the maximum speed of 20000rpm / min;
• Speed control mode : analog quantity 0-5V,???according to the users’ requirement we can set PWM within 10Hz-300Hz;
• It has have EN, DIR signal control side;
• It can output tachometer pulse;
• It has over-current, overvoltage, under voltage , overheating, motor stalling and other protection functions.

Product Overview:

• JKBLD480brushless DC motor driver is our company's latest high-tech product for the field of medium power motor drive. This product uses a large-scale integrated circuit to replace the original hardware. It has higher anti-jamming and fast response ability. It is suitable for all the three-phase brushless DC motors with low voltage DC18V-50V(boards show DC24V-48V) and peak current below 10A. Even if working with large current, it is still in low temperature. It is widely used in knitting equipment, medical equipment, food packaging machinery, power tools and a series of areas of electrical automation and control.

Electrical Specification :

• Power supply : DC18V 50V direct current (Capacity according to motor power selection).
• The maximum input current : Not greater than10A (according to motor and rated load).
• The maximum power : The maximum is 480W (over power motor is strictly prohibited).
• Insulation resistance : General temperature 500MΩ.
• Insulation strength : General temperature and pressure 0.5KV, 1minitute.

Environmental Parameters:

• Cooling method : Natural air cooling (forced air cooling is recommended)
• Environment Condition : Avoid dust, oil mist and corrosive gases
• Environment Temperature : 0 50 Deg C
• Environment Humidity : < 80%RH no condensation, no frost
• Environment Vibration : < 0.5G 4.9m/s2  10Hz-60Hz (non-continuous operation)
• Reserved temperature : -20 Deg C +65 Deg C
• Size : 118mmX75.5mmX34mm
• Weight : About 0.3Kg

Main Features:

• It can be connected with an external speed display board JKBL01, showing the speed, set drive parameters;
• It has double speed closed current design with low speed torque and smooth operation;
• It has high speed output with the maximum speed of 10000rpm / min;
• The speed control mode is an external PWM speed and external potentiometer speed;
• It has have EN, DIR,X1 signal control side;
• It can output FG signals (optoelectronic isolation, gate output);
• It can output ALM signals for the user to detect (optoelectronic isolation, gate output);
• It has over-current, overvoltage, under voltage, fan control and Hall Sensor phase error, motor stalling and other protection functions

JK1100 is the latest high-tech product of our company, for the field of medium power motor drive. It uses a large-scale integrated circuit to replace the original hardware, so it has higher performance of anti-jamming and fast response ability. It is suitable for all the low voltage three-phase brushless DC motors with peak current below 5A and low voltage AC80V-250V (boards show AC80V-220V), whether the motor driver with Hall or not. It is widely used in knitting equipment, medical equipment, food packaging machinery, electric tools and a series of electrical automation control area.
Electrical Specification:

• Power supply : AC80V - 220V direct current (Capacity according to motor power selection)
• The maximum input current : Not greater than 5A (according to motor and rated load)
• The maximum power : The maximum is 1100W (over power motor is strictly prohibited)
• Adaptable motor : Adaptable output power < 750W motor
• Insulation resistance : General temperature > 500M Ohms
• Insulation strength : General temperature and pressure 0.5KV, 1minitute

Environmental Parameter:

• Cooling method : Natural air cooling & forced air cooling
• Environment
• Environment Condition : Avoid dust, oil mist and corrosive gases
• Environment Temperature : 0 to 50 Deg C
• Environment Humidity : < 80%RH???no condensation, no frost
• Environment Vibration : < 0.5G (4.9m/s2) 10Hz-60Hz (non-continuous operation)
• Reserved temperature : -20 deg C +65 deg C
• Size : 150mmX97.5mmX53mm
• Weight : Approx 0.55Kg

The JKBLD300 is a high performance, cost-effective 3 phase BLDC motor drive which can provide power output 300VA max. The design is based on advanced DSP technology and feature high torque, low noise, low vibration, PID speed loop, PID current loop, over current protection, over load protection.
Electrical parameters:

• Hall Effect Angle - 120/240 deg
• Power Supply Input Voltage - 18 - 50 V
• Driver Current Output - 35 A
• Motor Speed - 20000 RPM
• Hall Signal Voltage - Min 4.5 to Max 5.5 V
• Hall Signal Current - 20 mA
• External Potentiometer - 10K Ohms

Connection Details:

• DC+/DC- : DC Power Input DC24V~DC48V
• U,V,W : Motor lead wire
• Hu, Hv, Hw : Hall sensor lead wire
• REF+ : Hall sensor power supply +
• REF- : Hall sensor power supply -
• VCC : External potentiometer power supply +
• SV : External potentiometer
• COM : Public (low level)
• F/R : Direction: High level/CW Low Level/CCW
• EN : Enable: High Level/Stop Low Level/Run
• BRK : Quick Brake: High Level/Stop Low Level/Run
• SPEED : Speed signal output
• ALARM : Alarm signal output

Speed Adjustment Instruction:

• Motor speed adjusted by the internal potentiometer RV
• Motor speed adjusted by the external potentiometer
• Motor speed adjusted by analog signal 0V~+5V input
• Motor speed adjusted by analog signal 0V~+10V input
• Motor speed adjusted by PWM input
• Pulse duty ratio 10%-90% / Speed linear modulation
• Pulse rate: 1K-10K/ pulse amplitude 5V

Motor Speed Quick Response Setting:

• OP/CLConnected (user setting) : PID Closed loop Motor quick response
• OP/CL Disconnected (factory setting) : NO PID Closed loop Motor normal response
• LeadWire Connection : Take care of the sequence of U,V,W